Installation Accessories for Metal Roofing

Installation accessories for Weckman Progantti roof



Progantti roofing sheet
Effective width 475 mm.


Wide ridge capping L=2 m
The widest ridge capping on the market makes installation easy and gives margins.


Ridge seal L~464 mm
Improves the ventilation of the roof. Colour RR23.


Gable flashing L=length of the roof (up to 10 m only with Progantti orders)
Flashing the same length as the roof (max. 10 m) in one piece without seams.


Lower eaves flashing L=2 m
Adjustable lower eaves flashing that facilitates the installation of gutters and controls the eaves line.


Mitre plate, full width L = 2 m
Full-width mitre plate that ensures waterproofness even in gently sloping Progantti roofs.


Gasket tape
For the sealing of mitres. With adhesive surface.


Damping strip
Reduces noise caused by wind, quick and easy to install.


End-wall flashing to the side L=2 m
For roof-to-wall connections.


End-wall flashing L=2 m
Available pre-bent to the correct angle.


Lower flashing, galvanised L=2 m
Necessary at the eaves under the gable flashing – keeps the gable boards dry.


Drain/radon ventilation pipe
Insulated 110. Complete set, includes Progantti lead-through.


Ventilation outlet pipe
Insulated 125/160 mm. Complete set, includes Progantti lead-through.


Lead-through rubber
25-70 mm, 50-100 mm, 90-150 mm, 125-200 mm


Roof hatch
Passage size 600 x 600 mm. Includes hinges and lock.


Ventilation spring
Keeps the ventilation channels open in a ventilated ridge construction also in winter conditions.


Side fastener, galvanised
Allows free thermal movements at the edge of the roof, prevents wrinkling and noise.


Upper eaves flashing L=2 m
For pent roof ridges. Available pre-bent to the correct angle.


Hip seal flashing L = 2 m
Perforated sealing flashing that prevents snow and water from entering the underlying structures and improves ventilation. Colour RR23.


Roofing screws 4.8 x 28
For attaching the bottom edge of mitre-cut roofing sheets and flashings.


Progantti-screws RST 4,2 x 25


Roof Sheet


Profiled Ridge Flashing L=1.93 m
For tile profile roofs. Recommended for roof pitches
shallower than 1:2.


Gable Flashing L=2 m


Junction Flashing L=2 m
Available pre-bent to a right angle.


Eaves Flashing L=2 m


Underlayment Flashing L=2 m
Essential at eaves edges under the gable flashing - prevents fascia boards from getting wet.
Profile-specific.


Eaves Sheet, Full Width L=2 m


Roof Hatch
Access opening size 600 x 600 mm. Includes hinges and lock.


Penetration Pipe Base Plate L=1 m
For profiled sheet roofs. Used together with insulated penetration pipes.


Valley End Cap
For use with profiled ridge flashing.


Sewer Ventilation Pipe
Insulated 110. Complete set, includes roof penetration and for profiled sheets also base plate (no. 10).


Ventilation Exhaust Pipe
Insulated 125/160 mm. Complete package, also includes roof penetration and for profiled sheets also base plate (no. 10).


Ventilation Cap
For profiled and smooth ridge flashing.


Y-Piece
For use with profiled ridge flashing.


T-Piece
For use with profiled ridge flashing.


Penetration Boot
25–70 mm, 50–100 mm,
90–150 mm, 125–200 mm


Profiled Ridge Flashing End Cap


Seals
Suitable seals are available for all Weckman profiles. Sealing tape 3 x 10 mm for side and longitudinal laps. Sealing mat for use with profiled ridge flashing at ridge and valley.


Roofing Screws 4.8 x 28
Roofing screws with sealing washers are supplied galvanized and in standard colors.


Touch-Up Paint
25 ml, standard colors


